Nummer Serie DS209 bootet 30min

[slank]

Hallo Community,

Meine DS209 bootet seit eine Woche über eine halbe Stunde, .
Die messages.log habe ich mir bereits angeschaut (und auch hier gebostet) und nichts auffälliges gesehen.
Connect via Webinterface oder ssh dauert ca.5min.
Shareconnect dauern auch entsprechend lange.

Heute habe ich die Box mal resetet. Mit dem Assistant gesucht, gefunden, config eingespielt, neu gebootet und der Assistant sagt keine "Nicht Konfiguriert".
Also "neu Installation" mit dem Assistant durchgeführt. Dieser hat nach dem einspielen der aktuellen Firmware abgebrochen, da er nach 400Sekunden die Box nicht gefunden hat.
Irgendwann war die Box wieder online und der Assistant sagt wieder "Nicht konfiguriert".

Die Box läuft jeden Tag ca. 12 Stunden (ca. 3 1/2 Jahre).

Kann es sein, dass die Box einfach ihren Zenit erreicht hat??

Vielleicht hat jemand noch eine Idee??

DiskStation> dmesg
[ 0.000000] Linux version 2.6.32.12 (root@build2) (gcc version 4.2.1) #3202 Fri Mar 1 01:06:07 CST 2013
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Sys Clk = 200000000, Tclk = 166666667
[ 0.000000] Synology Board ID: 21
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat c0418834, node_mem_map c0c01000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS209v10 ihd_num=2 netif_num=1
[ 0.000000] Synology Hardware Version: DS209v10-j
[ 0.000000] Internal HD num: 2
[ 0.000000] Internal netif num: 1
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 128MB 128MB = 256MB total
[ 0.000000] Memory: 244736KB available (3688K code, 538K data, 124K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
[ 0.240000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] xor: measuring software checksum speed
[ 0.290000] arm4regs : 1084.400 MB/sec
[ 0.340000] 8regs : 822.800 MB/sec
[ 0.390000] 32regs : 922.800 MB/sec
[ 0.390000] xor: using function: arm4regs (1084.400 MB/sec)
[ 0.390000] NET: Registered protocol family 16
[ 0.390000] Feroceon L2: Enabling L2
[ 0.390000] Feroceon L2: Cache support initialised, in WT override mode.
[ 0.400000]
[ 0.400000] CPU Interface
[ 0.400000] -------------
[ 0.400000] SDRAM_CS0 ....base 00000000, size 128MB
[ 0.400000] SDRAM_CS1 ....base 08000000, size 128MB
[ 0.400000] SDRAM_CS2 ....disable
[ 0.400000] SDRAM_CS3 ....disable
[ 0.400000] PEX0_MEM ....base e0000000, size 128MB
[ 0.400000] PEX0_IO ....base f2000000, size 1MB
[ 0.400000] PEX1_MEM ....no such
[ 0.400000] PEX1_IO ....no such
[ 0.400000] INTER_REGS ....base f1000000, size 1MB
[ 0.400000] NFLASH_CS ....base fa000000, size 2MB
[ 0.400000] SPI_CS ....base f4000000, size 16MB
[ 0.400000] BOOT_ROM_CS ....no such
[ 0.400000] DEV_BOOTCS ....no such
[ 0.400000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.400000] Detected Tclk 200000000 and SysClk 400000000
[ 0.400000] Synology 6281 1, 2 bay GPIO Init
[ 0.400000]
[ 0.400000] Warning PCI-E is Powered Off
[ 0.410000] bio: create slab <bio-0> at 0
[ 0.410000] vgaarb: loaded
[ 0.410000] SCSI subsystem initialized
[ 0.410000] libata version 3.00 loaded.
[ 0.580000] raid6: int32x1 97 MB/s
[ 0.750000] raid6: int32x2 111 MB/s
[ 0.920000] raid6: int32x4 124 MB/s
[ 1.090000] raid6: int32x8 108 MB/s
[ 1.090000] raid6: using algorithm int32x4 (124 MB/s)
[ 1.090000] Switching to clocksource kw_clocksource
[ 1.090000] NET: Registered protocol family 2
[ 1.090000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.090000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.090000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 1.090000] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.090000] TCP reno registered
[ 1.090000] NET: Registered protocol family 1
[ 1.090000] RPC: Registered udp transport module.
[ 1.090000] RPC: Registered tcp transport module.
[ 1.090000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.090000] Trying to unpack rootfs image as initramfs...
[ 2.090000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 2.100000] Freeing initrd memory: 4096K
[ 2.100000] XOR registered 4 channels
[ 2.100000] XOR 2nd invalidate WA enabled
[ 2.100000] VFS: Disk quotas dquot_6.5.2
[ 2.100000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.100000] msgmni has been set to 486
[ 2.100000] alg: No test for md5 (md5-generic)
[ 2.100000] alg: No test for des (des-generic)
[ 2.100000] alg: No test for des3_ede (des3_ede-generic)
[ 2.100000] alg: No test for stdrng (krng)
[ 2.100000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 2.100000] io scheduler noop registered
[ 2.100000] io scheduler anticipatory registered (default)
[ 2.110000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.110000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 2.120000] console [ttyS0] enabled
[ 2.120000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 2.130000] brd: module loaded
[ 2.140000] sata_mv sata_mv.0: version 1.28
[ 2.140000] sata_mv sata_mv.0: slots 32 ports 2
[ 2.150000] scsi0 : sata_mv
[ 2.150000] scsi1 : sata_mv
[ 2.150000] ata1: SATA max UDMA/133 irq 21
[ 2.160000] ata2: SATA max UDMA/133 irq 21
[ 2.510000] ata1: SATA link down (SStatus 0 SControl F300)
[ 2.600000] ata1: device plugged sstatus 0x123
[ 5.510000] Delay 5 seconds to wait for disk 2 ready.
[ 10.520000] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[ 10.520000] ata1: edma_err_cause=00000010 pp_flags=00000000, dev connect
[ 10.530000] ata1: SError: { PHYRdyChg DevExch }
[ 10.540000] ata1: hard resetting link
[ 11.050000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 11.090000] ata2.00: ATA-8: WDC WD10EADS-00M2B0, 01.00A01, max UDMA/133
[ 11.090000] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 11.140000] ata2.00: configured for UDMA/133
[ 11.140000] scsi 1:0:0:0: Direct-Access WDC WD10EADS-00M2B0 01.0 PQ: 0 ANSI: 5
[ 11.150000] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 11.160000] sd 1:0:0:0: [sdb] Write Protect is off
[ 11.160000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 11.160000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 11.170000] sdb: sdb1 sdb2 sdb3
[ 11.200000] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 15.060000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 15.260000] ata1.00: ATA-8: WDC WD10EADS-00M2B0, 01.00A01, max UDMA/133
[ 15.260000] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 15.310000] ata1.00: configured for UDMA/133
[ 15.310000] ata1: EH complete

 

[slank]

Zweiter Teil von dmesg:

[ 15.310000] scsi 0:0:0:0: Direct-Access WDC WD10EADS-00M2B0 01.0 PQ: 0 ANSI: 5
[ 15.320000] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 15.330000] sd 0:0:0:0: [sda] Write Protect is off
[ 15.330000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 15.330000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 15.340000] sda: sda1 sda2 sda3
[ 15.360000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 15.360000] physmap platform flash device: 00400000 at f8000000
[ 15.370000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[ 15.380000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f0000
[ 15.400000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[ 15.410000] SYNOMTD flash bank 0: Using RedBoot partition definition
[ 15.410000] Creating 6 MTD partitions on "SYNOMTD-0":
[ 15.420000] 0x000000000000-0x000000080000 : "RedBoot"
[ 15.420000] 0x000000080000-0x000000280000 : "zImage"
[ 15.430000] 0x000000280000-0x0000003c0000 : "rd.gz"
[ 15.440000] 0x0000003c0000-0x0000003d0000 : "vendor"
[ 15.440000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 15.450000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 15.450000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 15.460000] serial number='94F6N03419'
[ 15.460000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[ 15.470000] 0x0000003f0000-0x000000400000 : "FIS directory"
[ 15.480000] mvCpuIfTargetWinBaseLowGet:ERR. Getting target 11 failed.
[ 15.480000] mvCpuIfTargetWinSizeGet:ERR. Getting target 11 failed.
[ 15.490000]
[ 15.490000] ERROR: flashInfoFill - Failed to get Device Base address and Size (spi_flash 0)Loading Marvell Ethernet Driver:
[ 15.500000] o Cached descriptors in DRAM
[ 15.510000] o DRAM SW cache-coherency
[ 15.510000] o 2 Giga ports supported
[ 15.510000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 15.520000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 15.520000] o TCP segmentation offload (TSO) supported
[ 15.530000] o Receive checksum offload supported
[ 15.530000] o Transmit checksum offload supported
[ 15.540000] o SKB Recycle supported - (Enabled)
[ 15.540000] o Rx descripors: q0=128
[ 15.550000] o Tx descripors: q0=532
[ 15.550000] o Loading network interface(s):
[ 15.560000] o register under mv88fx_eth platform
[ 15.560000] o eth0, ifindex = 2, GbE port = 0
[ 15.570000] o eth0, phy chipid = 1410e40, Support WOL = 0
[ 15.570000]
[ 15.570000] md: linear personality registered for level -1
[ 15.580000] md: raid0 personality registered for level 0
[ 15.590000] md: raid1 personality registered for level 1
[ 15.590000] md: raid10 personality registered for level 10
[ 15.600000] md: raid6 personality registered for level 6
[ 15.600000] md: raid5 personality registered for level 5
[ 15.610000] md: raid4 personality registered for level 4
[ 15.610000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 15.620000] cpuidle: using governor ladder
[ 15.630000] TCP cubic registered
[ 15.630000] NET: Registered protocol family 17
[ 15.630000] md: Waiting for all devices to be available before autodetect
[ 15.640000] md: If you don't use raid, use raid=noautodetect
[ 15.650000] md: Autodetecting RAID arrays.
[ 21.030000] md: invalid raid superblock magic on sda3
[ 21.040000] md: sda3 does not have a valid v0.90 superblock, not importing!
[ 21.090000] md: invalid raid superblock magic on sdb3
[ 21.100000] md: sdb3 does not have a valid v0.90 superblock, not importing!
[ 21.100000] md: Scanned 6 and added 4 devices.
[ 21.110000] md: autorun ...
[ 21.110000] md: considering sda1 ...
[ 21.110000] md: adding sda1 ...
[ 21.120000] md: sda2 has different UUID to sda1
[ 21.120000] md: adding sdb1 ...
[ 21.120000] md: sdb2 has different UUID to sda1
[ 21.130000] md: created md0
[ 21.130000] md: bind<sdb1>
[ 21.130000] md: bind<sda1>
[ 21.140000] md: running: <sda1><sdb1>
[ 21.140000] raid1: md0 is not clean -- starting background reconstruction
[ 21.150000] raid1: raid set md0 active with 2 out of 2 mirrors
[ 21.150000] md0: detected capacity change from 0 to 2549940224
[ 21.160000] md: considering sda2 ...
[ 21.160000] md: adding sda2 ...
[ 21.170000] md: adding sdb2 ...
[ 21.170000] md: resync of RAID array md0
[ 21.170000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 21.180000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[ 21.190000] md: using 128k window, over a total of 2490176 blocks.
[ 21.200000] md: resuming resync of md0 from checkpoint.
[ 21.200000] md: created md1
[ 21.200000] md: bind<sdb2>
[ 21.210000] md: bind<sda2>
[ 21.210000] md: running: <sda2><sdb2>
[ 21.210000] raid1: md1 is not clean -- starting background reconstruction
[ 21.220000] raid1: raid set md1 active with 2 out of 2 mirrors
[ 21.230000] md1: detected capacity change from 0 to 2147418112
[ 21.230000] md: ... autorun DONE.
[ 21.240000] md: delaying resync of md1 until md0 has finished (they share one or more physical units)
[ 21.250000] RAMDISK: lzma image found at block 0
[ 22.330000] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 22.370000] ds209_synobios: module license 'Synology Inc.' taints kernel.
[ 22.380000] Disabling lock debugging due to kernel taint
[ 22.450000] synobios: load, major number 201
[ 22.460000] Brand: Synology
[ 22.460000] Model: DS-209
[ 22.460000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 22.510000] synobios: unload
[ 24.840000] md0: unknown partition table
[ 36.880000] EXT4-fs (md0): barriers disabled
[ 36.900000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 37.220000] md1: unknown partition table
[ 42.330000] Adding 2097080k swap on /dev/md1. Priority:-1 extents:1 across:2097080k
[ 629.790000] synobios: load, major number 201
[ 629.800000] Brand: Synology
[ 629.800000] Model: DS-209
[ 629.800000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 629.840000] synobios: unload
[ 705.850000] synoacl module [synoacl_ext4] is not loaded
[ 705.860000] synoacl module [synoacl_vfs] is not loaded
[ 707.670000] EXT3-fs: md0: couldn't mount because of unsupported optional features (240).
[ 707.730000] EXT2-fs: md0: couldn't mount because of unsupported optional features (240).
[ 707.810000] EXT4-fs (md0): barriers disabled
[ 710.310000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 710.320000] VFS: Mounted root (ext4 filesystem) on device 9:0.
[ 710.320000] Trying to move old root to /initrd ... okay
[ 710.360000] Freeing init memory: 124K
[ 800.000000] Adding 2097080k swap on /dev/md1. Priority:-1 extents:1 across:2097080k
[ 810.360000] NET: Registered protocol family 10
[ 810.360000] lo: Disabled Privacy Extensions
[ 815.660000] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 815.690000] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 818.980000] usbcore: registered new interface driver usbfs
[ 818.990000] usbcore: registered new interface driver hub
[ 819.000000] usbcore: registered new interface driver ethub
[ 819.000000] usbcore: registered new device driver usb
[ 825.110000] cpufreq: Init kirkwood cpufreq driver
[ 825.110000] cpufreq: High frequency: 1200000KHz - Low frequency: 400000KHz
[ 827.610000] alg: No test for aes (aes-generic)
[ 829.430000] alg: No test for stdrng (ansi_cprng)
[ 831.290000] alg: No test for crc32c (crc32c-generic)
[ 831.400000] cesadev_init(bf137000)
[ 831.440000] mvCesaInit: sessions=10240, queue=64, pSram=f0000000
[ 831.500000] alg: No test for sha1 (sha1-generic)
[ 831.520000] alg: No test for sha224 (sha224-generic)
[ 831.520000] alg: No test for sha256 (sha256-generic)
[ 831.540000] alg: No test for sha384 (sha384-generic)
[ 831.550000] alg: No test for sha512 (sha512-generic)
[ 831.620000] encryptfs using the OCF package.
[ 831.870000] fuse init (API version 7.13)
[ 833.270000] sky2 driver version 1.25
[ 835.050000] synobios: load, major number 201
[ 835.050000] Brand: Synology
[ 835.060000] Model: DS-209
[ 835.060000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 869.690000] eth0: mac address changed
[ 871.780000] eth0: link down
[ 871.780000] eth0: started
[ 871.780000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 873.050000] eth0: link up, full duplex, speed 1 Gbps
[ 873.060000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 883.610000] eth0: no IPv6 routers present
[ 933.340000] md: md2 stopped.
[ 942.190000] md: bind<sdb3>
[ 945.610000] md: bind<sda3>
[ 945.610000] raid1: md2 is not clean -- starting background reconstruction
[ 945.620000] raid1: raid set md2 active with 2 out of 2 mirrors
[ 945.630000] md2: detected capacity change from 0 to 995370270720
[ 945.650000] md2:
[ 945.650000] md: delaying resync of md2 until md0 has finished (they share one or more physical units)
[ 947.850000] unknown partition table
[ 1022.710000] EXT4-fs (md2): barriers disabled
[ 1025.360000] EXT4-fs (md2): mounted filesystem with writeback data mode
[ 1082.610000] ata2.00: configured for UDMA/133
[ 1082.610000] ata2: EH complete
[ 1082.610000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1088.070000] ata1.00: configured for UDMA/133
[ 1088.070000] ata1: EH complete
[ 1104.050000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

 

[slank]

dritter und letzter Teil ;-)

[ 1104.050000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 1104.060000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 1104.080000] ata2.00: Disable disk write cache in EH
[ 1104.110000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 1104.130000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 1104.130000] usb usb1: configuration #1 chosen from 1 choice
[ 1104.160000] hub 1-0:1.0: USB hub found
[ 1104.160000] hub 1-0:1.0: 1 port detected
[ 1104.190000] ata2.00: configured for UDMA/133
[ 1104.190000] ata2: EH complete
[ 1104.190000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1104.480000] usb 1-1: new high speed USB device using orion-ehci and address 2
[ 1104.630000] Got empty serial number. Generate serial number from product.
[ 1104.630000] usb 1-1: configuration #1 chosen from 1 choice
[ 1104.650000] hub 1-1:1.0: USB hub found
[ 1104.650000] hub 1-1:1.0: 4 ports detected
[ 1105.450000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1114.560000] Initializing USB Mass Storage driver...
[ 1114.570000] usbcore: registered new interface driver usb-storage
[ 1114.570000] USB Mass Storage support registered.
[ 1118.650000] usbcore: registered new interface driver usblp
[ 1121.210000] usbcore: registered new interface driver hiddev
[ 1121.220000] usbcore: registered new interface driver usbhid
[ 1121.220000] usbhid: v2.6:USB HID core driver
[ 1161.350000] findhostd uses obsolete (PF_INET,SOCK_PACKET)
[ 2948.980000] loop: module loaded
[ 2960.200000] Slow work thread pool: Starting up
[ 2960.210000] Slow work thread pool: Ready
[ 3091.730000] md: md0: resync done.
[ 3091.750000] md: resync of RAID array md2
[ 3091.760000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 3091.760000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[ 3091.770000] md: using 128k window, over a total of 972041280 blocks.
[ 3091.780000] md: resuming resync of md2 from checkpoint.
[ 3091.790000] md: delaying resync of md1 until md2 has finished (they share one or more physical units)
[ 3096.490000] RAID1 conf printout:
[ 3096.490000] --- wd:2 rd:2
[ 3096.490000] disk 0, wo:0, o:1, dev:sda1
[ 3096.500000] disk 1, wo:0, o:1, dev:sdb1

 

[Benares]

Also das ist wirklich nicht normal. Poste mal die Ausgabe von "dmesg" (Kernel-Meldungen), vielleicht sieht man da, was bei diesen Zeitsprüngen passiert.

Gruß Benares

 

[slank]

@Der dreiteiler über Deinem Post ist doch die Ausgabe von dmesg

Die Message Log steht im folgendem Post:
http://www.synology-forum.de/showth...-Informationen&p=319429&viewfull=1#post319429

Scheinbar scheinen das meine Probleme zu sein:

[ 24.840000] md0: unknown partition table
[ 36.880000] EXT4-fs (md0): barriers disabled
[ 36.900000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 37.220000] md1: unknown partition table
[ 42.330000] Adding 2097080k swap on /dev/md1. Priority:-1 extents:1 across:2097080k
[ 629.790000] synobios: load, major number 201
[ 629.800000] Brand: Synology
[ 629.800000] Model: DS-209
[ 629.800000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 629.840000] synobios: unload
[ 705.850000] synoacl module [synoacl_ext4] is not loaded
[ 705.860000] synoacl module [synoacl_vfs] is not loaded
[ 707.670000] EXT3-fs: md0: couldn't mount because of unsupported optional features (240).
[ 707.730000] EXT2-fs: md0: couldn't mount because of unsupported optional features (240).
[ 707.810000] EXT4-fs (md0): barriers disabled
[ 710.310000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 710.320000] VFS: Mounted root (ext4 filesystem) on device 9:0.
[ 710.320000] Trying to move old root to /initrd ... okay
[ 710.360000] Freeing init memory: 124K
[ 800.000000] Adding 2097080k swap on /dev/md1. Priority:-1 extents:1 across:2097080k

Gruß
Slank

 

[slank]

Scheinbar habe ich ein größeres Problem mit meinem Raid:

DiskStation> cat /proc/mdstat
Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4]
md2 : active raid1 sda3[0] sdb3[1]
972041280 blocks super 1.1 [2/2] [UU]
[==================>..] resync = 93.4% (908072448/972041280) finish=2328689.1min speed=0K/sec

md1 : active raid1 sda2[0] sdb2[1]
2097088 blocks [2/2] [UU]
resync=DELAYED

md0 : active raid1 sda1[0] sdb1[1]
2490176 blocks [2/2] [UU]

Wenn ich das richtig interpretiere, versucht die Box das raid md2 zu syncen und bleibt dabei hängen.
Was kann ich tun?
Hat jemand noch Tipps für mich?

Was kann die Ursache des ganzen sein? Sollte ich die Platten mal wechseln?

Gruß
slank

 

[Benares]

@Der dreiteiler über Deinem Post ist doch die Ausgabe von dmesg

Sorry, ich dachte das sei die /var/log/messages.

Läuft den der Rebuild weiter oder bleibt er bei 93.4% stehen?

 

[slank]

Guten Morgen,

um 7Uhr hat er alles resynced.
Systemconfig eingespielt, reboot. Beim abgeben von reboot braucht das System schon 4min bis es ssh trennt.
Nach 20min ist das System online und hat noch die alte Config und nicht die gewünschte

DiskStation> cat /proc/mdstat
Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4]
md2 : active raid1 sda3[0] sdb3[1]
972041280 blocks super 1.1 [2/2] [UU]

md1 : active raid1 sda2[0] sdb2[1]
2097088 blocks [2/2] [UU]

md0 : active raid1 sda1[0] sdb1[1]
2490176 blocks [2/2] [UU]

unused devices: <none>

Auszug aus dmesg:

[ 24.280000] md0: unknown partition table
[ 38.540000] EXT4-fs (md0): barriers disabled
[ 38.560000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 48.780000] synoacl module [synoacl_ext4] is not loaded
[ 48.780000] synoacl module [synoacl_vfs] is not loaded
[ 48.820000] EXT3-fs: md0: couldn't mount because of unsupported optional features (240).
[ 48.820000] EXT2-fs: md0: couldn't mount because of unsupported optional features (240).
[ 48.840000] EXT4-fs (md0): barriers disabled
[ 50.590000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 50.590000] VFS: Mounted root (ext4 filesystem) on device 9:0.
[ 50.600000] Trying to move old root to /initrd ... okay
[ 50.610000] Freeing init memory: 124K
[ 108.000000] md1: unknown partition table
[ 109.480000] Adding 2097080k swap on /dev/md1. Priority:-1 extents:1 across:2097080k
[ 116.460000] NET: Registered protocol family 10
[ 116.460000] lo: Disabled Privacy Extensions
[ 116.570000] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 116.580000] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 116.720000] usbcore: registered new interface driver usbfs
[ 116.730000] usbcore: registered new interface driver hub
[ 116.730000] usbcore: registered new interface driver ethub
[ 116.740000] usbcore: registered new device driver usb
[ 116.880000] cpufreq: Init kirkwood cpufreq driver
[ 116.880000] cpufreq: High frequency: 1200000KHz - Low frequency: 400000KHz
[ 116.990000] alg: No test for aes (aes-generic)
[ 117.020000] alg: No test for stdrng (ansi_cprng)
[ 117.040000] alg: No test for crc32c (crc32c-generic)
[ 117.110000] cesadev_init(bf129000)
[ 117.130000] mvCesaInit: sessions=10240, queue=64, pSram=f0000000
[ 117.180000] alg: No test for sha1 (sha1-generic)
[ 117.190000] alg: No test for sha224 (sha224-generic)
[ 117.200000] alg: No test for sha256 (sha256-generic)
[ 117.220000] alg: No test for sha384 (sha384-generic)
[ 117.220000] alg: No test for sha512 (sha512-generic)
[ 117.280000] encryptfs using the OCF package.
[ 117.500000] fuse init (API version 7.13)
[ 117.680000] sky2 driver version 1.25
[ 117.810000] synobios: load, major number 201
[ 117.820000] Brand: Synology
[ 117.820000] Model: DS-209
[ 117.820000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 145.200000] eth0: mac address changed
[ 147.280000] eth0: link down
[ 147.290000] eth0: started
[ 147.290000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 148.420000] eth0: link up, full duplex, speed 1 Gbps
[ 148.420000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 159.340000] eth0: no IPv6 routers present
[ 185.660000] md: md2 stopped.
[ 187.490000] md: bind<sdb3>
[ 189.250000] md: bind<sda3>
[ 189.260000] raid1: raid set md2 active with 2 out of 2 mirrors
[ 189.260000] md2: detected capacity change from 0 to 995370270720
[ 189.280000] md2: unknown partition table
[ 295.800000] EXT4-fs (md2): barriers disabled
[ 298.600000] EXT4-fs (md2): mounted filesystem with writeback data mode
[ 377.350000] ata2.00: configured for UDMA/133
[ 377.350000] ata2: EH complete
[ 377.350000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 383.410000] ata1.00: configured for UDMA/133
[ 383.410000] ata1: EH complete
[ 393.420000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 393.430000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 393.430000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 393.470000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 393.490000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 393.490000] usb usb1: configuration #1 chosen from 1 choice
[ 393.520000] hub 1-0:1.0: USB hub found
[ 393.520000] hub 1-0:1.0: 1 port detected
[ 393.570000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 393.840000] usb 1-1: new high speed USB device using orion-ehci and address 2
[ 393.930000] Initializing USB Mass Storage driver...
[ 393.940000] usbcore: registered new interface driver usb-storage
[ 393.940000] USB Mass Storage support registered.
[ 393.990000] Got empty serial number. Generate serial number from product.
[ 394.000000] usb 1-1: configuration #1 chosen from 1 choice
[ 394.000000] hub 1-1:1.0: USB hub found
[ 394.040000] hub 1-1:1.0: 4 ports detected
[ 394.150000] usbcore: registered new interface driver usblp
[ 394.430000] usbcore: registered new interface driver hiddev
[ 394.490000] usbcore: registered new interface driver usbhid
[ 394.490000] usbhid: v2.6:USB HID core driver
[ 395.170000] ata2.00: Disable disk write cache in EH
[ 395.290000] ata2.00: configured for UDMA/133
[ 395.290000] ata2: EH complete
[ 395.290000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 862.730000] findhostd uses obsolete (PF_INET,SOCK_PACKET)
[ 1254.600000] loop: module loaded
[ 1255.810000] Slow work thread pool: Starting up
[ 1256.480000] Slow work thread pool: Ready

Bin etwas ratlos.

Vielen Dank für euren Support ;-)
Gruß
slank

 

[slank]

Nabend,

schreibe mal meine Erkenntnisstand ;-)

Mein System ist ja wie berichtet im Raid Modus.
Wenn ich einen S.M.A.R.T. Test durchführe bleibt der Scan bei einer Platte bei 90% stehen (seid ca. 6 Stunden). Die zweite Platte geht sauber durch.
Scheinbar bin ich nicht der einzige ;-)

http://forum.synology.com/enu/viewtopic.php?f=19&t=58635

Habe mal an den Support geschrieben, mal schauen was sich da noch tut ;-)

Gruß und gute Nacht
slank