Due to Power Failure during update My NAS (Synology DS214Se) not booting. Synology assistant Not Detecting my NAS.
I have connected DS214Se using USB to Serial TTL adapter via Serial port on Motherboard of Synology DS214Se. I got it connected via extraputty and the rest is mentioned below.
Need Help to recover my DS214Se.
BootROM 1.08
Booting from SPI flash
High speed PHY - Version: 2.1.2 (COM-PHY-V20)
Update PEX Device ID 0x67100
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 4.5.0
DDR3 Training Sequence - Ended Successfully
Status = MV_OK
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-SYNO-944e83b-2013-08-13 (Aug 14 2013 - 14:05:18) Marvell version: v2011.12 2013_Q1.2
Board: SYNO-DS214se-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 800 [MHz]
L2 @ 533 [MHz]
TClock @ 200 [MHz]
DDR @ 533 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 256 MiB
Map: Code: 0x0ff09000:0x0ffa1354
BSS: 0x0ffef0a0
Stack: 0x0f9f8ef8
Heap: 0x0f9f9000:0x0ff09000
MMC: MRVL_MMC: 0
SF: Detected M25P64 with page size 64 KiB, total 8 MiB
*** Warning - bad CRC, using default environment
PEX 0.0(0): Detected No Link.
PEX 0.1(1): Detected No Link.
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Modules/Interfaces Detected:
RGMII0 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Synology Model: DS214se
Fan Status: Good
Net: egiga0 [PRIME]
Press Ctrl+C to abort autoboot in 3 second
SF: Detected M25P64 with page size 64 KiB, total 8 MiB
## Booting kernel from Legacy Image at f40c0000 ...
Image Name: Linux-3.2.40
Created: 2017-10-06 10:13:18 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2157536 Bytes = 2.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
Marvell>> setenv ipaddr 192.168.1.15
Marvell>> setenv serverip 192.168.1.3
Marvell>> setenv gatewayip 192.168.1.1
Marvell>> tftpboot 0x2000000 zImage
Using egiga0 device
TFTP from server 192.168.1.3; our IP address is 192.168.1.15
Filename 'zImage'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################
done
Bytes transferred = 2157304 (20eaf8 hex)
Marvell>> tftpboot 0x3000000 rd.bin
Using egiga0 device
TFTP from server 192.168.1.3; our IP address is 192.168.1.15
Filename 'rd.bin'.
Load address: 0x3000000
Loading: #################################################################
#################################################################
#################################################################
#######################################################
done
Bytes transferred = 3669524 (37fe14 hex)
Marvell>> tftpboot 0x4000000 uboot_DS214se.bin
Using egiga0 device
TFTP from server 192.168.1.3; our IP address is 192.168.1.15
Filename 'uboot_DS214se.bin'.
Load address: 0x4000000
Loading: ###################################################
done
Bytes transferred = 742968 (b5638 hex)
Marvell>> bootm 0x2000000 0x3000000 0x4000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-3.2.40
Created: 2017-11-10 12:07:36 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2157240 Bytes = 2.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 03000000 ...
Image Name: synology_armada370_214se 15217
Created: 2017-11-10 15:39:43 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 3669460 Bytes = 3.5 MiB
Load Address: 08000000
Entry Point: 08000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
I have connected DS214Se using USB to Serial TTL adapter via Serial port on Motherboard of Synology DS214Se. I got it connected via extraputty and the rest is mentioned below.
Need Help to recover my DS214Se.
BootROM 1.08
Booting from SPI flash
High speed PHY - Version: 2.1.2 (COM-PHY-V20)
Update PEX Device ID 0x67100
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 4.5.0
DDR3 Training Sequence - Ended Successfully
Status = MV_OK
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12-SYNO-944e83b-2013-08-13 (Aug 14 2013 - 14:05:18) Marvell version: v2011.12 2013_Q1.2
Board: SYNO-DS214se-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 800 [MHz]
L2 @ 533 [MHz]
TClock @ 200 [MHz]
DDR @ 533 [MHz]
DDR 16Bit Width, FastPath Memory Access
DRAM: 256 MiB
Map: Code: 0x0ff09000:0x0ffa1354
BSS: 0x0ffef0a0
Stack: 0x0f9f8ef8
Heap: 0x0f9f9000:0x0ff09000
MMC: MRVL_MMC: 0
SF: Detected M25P64 with page size 64 KiB, total 8 MiB
*** Warning - bad CRC, using default environment
PEX 0.0(0): Detected No Link.
PEX 0.1(1): Detected No Link.
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Modules/Interfaces Detected:
RGMII0 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
SATA0 (Lane 2)
SATA1 (Lane 3)
Synology Model: DS214se
Fan Status: Good
Net: egiga0 [PRIME]
Press Ctrl+C to abort autoboot in 3 second
SF: Detected M25P64 with page size 64 KiB, total 8 MiB
## Booting kernel from Legacy Image at f40c0000 ...
Image Name: Linux-3.2.40
Created: 2017-10-06 10:13:18 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2157536 Bytes = 2.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
Marvell>> setenv ipaddr 192.168.1.15
Marvell>> setenv serverip 192.168.1.3
Marvell>> setenv gatewayip 192.168.1.1
Marvell>> tftpboot 0x2000000 zImage
Using egiga0 device
TFTP from server 192.168.1.3; our IP address is 192.168.1.15
Filename 'zImage'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################
done
Bytes transferred = 2157304 (20eaf8 hex)
Marvell>> tftpboot 0x3000000 rd.bin
Using egiga0 device
TFTP from server 192.168.1.3; our IP address is 192.168.1.15
Filename 'rd.bin'.
Load address: 0x3000000
Loading: #################################################################
#################################################################
#################################################################
#######################################################
done
Bytes transferred = 3669524 (37fe14 hex)
Marvell>> tftpboot 0x4000000 uboot_DS214se.bin
Using egiga0 device
TFTP from server 192.168.1.3; our IP address is 192.168.1.15
Filename 'uboot_DS214se.bin'.
Load address: 0x4000000
Loading: ###################################################
done
Bytes transferred = 742968 (b5638 hex)
Marvell>> bootm 0x2000000 0x3000000 0x4000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-3.2.40
Created: 2017-11-10 12:07:36 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2157240 Bytes = 2.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 03000000 ...
Image Name: synology_armada370_214se 15217
Created: 2017-11-10 15:39:43 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 3669460 Bytes = 3.5 MiB
Load Address: 08000000
Entry Point: 08000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Zuletzt bearbeitet: