Hier mal der CLI S.M.A.R.T.-Werte output
$ sudo smartctl -a -d sat /dev/sdb
Des wird jeweils nur der 2. Slot angesprochen. Ich habe entsprechend die Platten vorab getauscht
smartctl 6.5 (build date Sep 26 2022) [x86_64-linux-4.4.302+] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: HGST Ultrastar He10
Device Model: HGST HUH721010ALN600
HDD-1
Firmware Version: LHGNT384
User Capacity: 10,000,831,348,736 bytes [10.0 TB]
Sector Size: 4096 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri May 3 10:03:25 2024 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 93) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off supp ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: (1268) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VA LUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 10 0 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 13 4 134 054 Pre-fail Offline - 96
3 Spin_Up_Time 0x0007 15 1 151 024 Pre-fail Always - 434 (Average 439)
4 Start_Stop_Count 0x0012 10 0 100 000 Old_age Always - 1261
5 Reallocated_Sector_Ct 0x0033 10 0 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 10 0 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 12 8 128 020 Pre-fail Offline - 18
9 Power_On_Hours 0x0012 09 9 099 000 Old_age Always - 13091
10 Spin_Retry_Count 0x0013 10 0 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 10 0 100 000 Old_age Always - 1248
22 Helium_Level 0x0023 10 0 100 025 Pre-fail Always - 100
192 Power-Off_Retract_Count 0x0032 09 9 099 000 Old_age Always - 1828
193 Load_Cycle_Count 0x0012 09 9 099 000 Old_age Always - 1828
194 Temperature_Celsius 0x0002 21 4 214 000 Old_age Always - 28 (Min/Max 15/41)
196 Reallocated_Event_Count 0x0032 10 0 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 10 0 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 10 0 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 20 0 200 000 Old_age Always - 102
SMART Error Log Version: 1
ATA Error Count: 102 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 102 occurred at disk power-on lifetime: 10021 hours (417 days + 13 hours)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 01 18 fc ff 87 40 08 00:00:20.368 READ FPDMA QUEUED
60 01 10 fb ff 87 40 08 00:00:20.359 READ FPDMA QUEUED
60 01 08 ff ff 87 40 08 00:00:20.342 READ FPDMA QUEUED
60 01 00 05 00 00 40 08 00:00:20.342 READ FPDMA QUEUED
60 01 f0 04 00 00 40 08 00:00:20.342 READ FPDMA QUEUED
Error 101 occurred at disk power-on lifetime: 10012 hours (417 days + 4 hours)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 08 04 00 00 40 08 00:00:30.179 READ FPDMA QUEUED
60 10 18 0c 00 00 40 08 00:00:30.163 READ FPDMA QUEUED
2f 00 01 13 00 00 a0 08 00:00:30.153 READ LOG EXT
ef 10 02 00 00 00 a0 08 00:00:30.150 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 08 00:00:30.150 READ NATIVE MAX ADDRESS EXT [OBS-AC S-3]
Error 100 occurred at disk power-on lifetime: 10012 hours (417 days + 4 hours)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 f0 04 00 00 40 08 00:00:29.604 READ FPDMA QUEUED
60 04 e8 00 00 00 40 08 00:00:29.600 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 08 00:00:29.599 FLUSH CACHE EXT
60 01 80 fe ff 87 40 08 00:00:28.771 READ FPDMA QUEUED
60 01 78 fd ff 87 40 08 00:00:28.771 READ FPDMA QUEUED
Error 99 occurred at disk power-on lifetime: 10012 hours (417 days + 4 hours)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 01 d8 01 00 00 40 08 00:00:25.654 READ FPDMA QUEUED
60 01 d0 00 00 00 40 08 00:00:25.638 READ FPDMA QUEUED
ec 00 00 00 00 00 00 08 00:00:25.605 IDENTIFY DEVICE
2f 00 01 13 00 00 a0 08 00:00:25.595 READ LOG EXT
ef 10 02 00 00 00 a0 08 00:00:25.592 SET FEATURES [Enable SATA feature]
Error 98 occurred at disk power-on lifetime: 9999 hours (416 days + 15 hours)
When the command that caused the error occurred, the device was active or idle .
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 04 90 00 00 00 40 08 00:00:21.310 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 08 00:00:21.291 FLUSH CACHE EXT
60 01 28 fe ff 87 40 08 00:00:20.307 READ FPDMA QUEUED
60 01 20 fd ff 87 40 08 00:00:20.307 READ FPDMA QUEUED
60 01 18 fc ff 87 40 08 00:00:20.307 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error
# 1 Short offline Completed without error 00% 13090 -
# 2 Short offline Completed without error 00% 9858 -
# 3 Short offline Completed without error 00% 9624 -
# 4 Short offline Completed without error 00% 9418 -
# 5 Short offline Completed without error 00% 9178 -
# 6 Short offline Completed without error 00% 8688 -
# 7 Short offline Completed without error 00% 7763 -
# 8 Short offline Completed without error 00% 7227 -
# 9 Short offline Completed without error 00% 6942 -
#10 Short offline Completed without error 00% 6680 -
#11 Short offline Completed without error 00% 6326 -
#12 Short offline Completed without error 00% 6055 -
#13 Short offline Completed without error 00% 5679 -
#14 Short offline Completed without error 00% 4985 -
#15 Short offline Completed without error 00% 4617 -
#16 Short offline Completed without error 00% 4345 -
#17 Short offline Completed without error 00% 4279 -
#18 Short offline Completed without error 00% 3661 -
#19 Short offline Completed without error 00% 2801 -
#20 Short offline Completed without error 00% 468 -
#21 Short offline Completed without error 00% 156 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
*************************************************************************
-------------------------------------------------------------------------
************************************************************************
=== START OF INFORMATION SECTION ===
Model Family: HGST Ultrastar He10
Device Model: HGST HUH721010ALN600
HDD-2
Firmware Version: LHGNT384
User Capacity: 10,000,831,348,736 bytes [10.0 TB]
Sector Size: 4096 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri May 3 17:08:50 2024 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 93) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off supp ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: (1147) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VA LUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 10 0 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 13 4 134 054 Pre-fail Offline - 96
3 Spin_Up_Time 0x0007 14 7 147 024 Pre-fail Always - 445 (Average 452)
4 Start_Stop_Count 0x0012 10 0 100 000 Old_age Always - 1298
5 Reallocated_Sector_Ct 0x0033 10 0 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 10 0 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 12 8 128 020 Pre-fail Offline - 18
9 Power_On_Hours 0x0012 09 9 099 000 Old_age Always - 13239
10 Spin_Retry_Count 0x0013 10 0 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 10 0 100 000 Old_age Always - 1285
22 Helium_Level 0x0023 10 0 100 025 Pre-fail Always - 100
192 Power-Off_Retract_Count 0x0032 09 9 099 000 Old_age Always - 1868
193 Load_Cycle_Count 0x0012 09 9 099 000 Old_age Always - 1868
194 Temperature_Celsius 0x0002 21 4 214 000 Old_age Always - 28 (Min/Max 16/40)
196 Reallocated_Event_Count 0x0032 10 0 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 10 0 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 10 0 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 20 0 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error
# 1 Short offline Completed without error 00% 9998 -
# 2 Short offline Completed without error 00% 9764 -
# 3 Short offline Completed without error 00% 9558 -
# 4 Short offline Completed without error 00% 9318 -
# 5 Short offline Completed without error 00% 8827 -
# 6 Short offline Completed without error 00% 7902 -
# 7 Short offline Completed without error 00% 7366 -
# 8 Short offline Completed without error 00% 7080 -
# 9 Short offline Completed without error 00% 6818 -
#10 Short offline Completed without error 00% 6463 -
#11 Short offline Completed without error 00% 6192 -
#12 Short offline Completed without error 00% 5816 -
#13 Short offline Completed without error 00% 5121 -
#14 Short offline Completed without error 00% 4753 -
#15 Short offline Completed without error 00% 4481 -
#16 Short offline Completed without error 00% 4415 -
#17 Short offline Completed without error 00% 3796 -
#18 Short offline Completed without error 00% 2936 -
#19 Short offline Completed without error 00% 601 -
#20 Short offline Completed without error 00% 289 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
