Nach Stromausfall - DS 411j bootet nicht mehr richtig

[Daydreamer]

Jetzt kam so viel, dass der Puffer von Putty scheibar voll ist:

:: Loading module vfat ... [ OK ]
:: Loading module fuse[ 39.470000] fuse init (API version 7.13)
... [ OK ]
:: Loading module hfsplus ... [ OK ]
:: Loading module synoacl_vfs ... [ OK ]
:: Loading module synoacl_ext4 ... [ OK ]
:: Mounting usbfs ... [ OK ]
:: Loading module sky2[ 39.670000] sky2 driver version 1.25
... [ OK ]
:: Loading module synobios[ 39.770000] correction with 0x00
[ 39.840000] synobios: load, major number 201
[ 39.840000] Brand: Synology
[ 39.850000] Model: DS-211j
[ 39.850000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
... [ OK ]
synochecknetworkcfg: Pass
[ 40.290000] eth0: mac address changed
[ 42.370000] eth0: link down
[ 42.370000] eth0: started
[ 42.380000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 42.720000] eth0: link up, full duplex, speed 1 Gbps
[ 42.730000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0 Link encap:Ethernet HWaddr 00:11:32:08:43:A6
inet6 addr: fe80::211:32ff:fe08:43a6/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:0 (0.0 B) TX bytes:150 (150.0 B)
Interrupt:11

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

ls: /etc/dhcpd/dhcpd-*.conf: No such file or directory
ls: /etc/dhcpd/dhcpd-*.info: No such file or directory
grep: /etc/dhcpd/dhcpd.info: No such file or directory
kernel.panic = 3
:: Starting syslogd ... [ OK ]
Pass s00_synocheckfstab ...
Pass CheckSynoinfo ...
Pass CheckUser
Pass CheckSmbConf ...
Pass CheckCronTab ...
Pass CheckGroup.
Pass s62_synocheckapple ...
start findhostd
synokerneltz: set kernel time zone to -60
kernel.core_pattern = /volume1/@%e.core
fs.suid_dumpable = 2
vm.min_free_kbytes = 8192
:: Starting scemd
[ 50.080000] ------------[ cut here ]------------
[ 50.080000] WARNING: at arch/arm/mach-feroceon-kw/./synology-gpio.c:213 SYNO_CTRL_INTERNAL_HDD_LED_SET+0x40/0xfc()
[ 50.090000] Modules linked in: ds211j_synobios(P) sky2 synoacl_ext4(P) synoacl_vfs(P) hfsplus fuse vfat fat cryptosoft ecryptfs sha512_generic sha256_generic sha1_generic ecb cesa_ocf_drv(P) cesa_dev cryptodev(P) ocf(P) chainiv des_generic crc32c eseqiv krng ansi_cprng rng aes_generic md5 cbc cryptomgr pcompress aead crypto_hash crypto_blkcipher crypto_wq crypto_algapi cpufreq cpufreq_stats freq_table dm_snapshot crc_itu_t crc_ccitt quota_v2 quota_tree usbcore sg psnap llc ipv6
[ 50.130000] [<c00efe6c>] (unwind_backtrace+0x0/0xe4) from [<c01165e4>] (warn_slowpath_common+0x50/0x68)
[ 50.140000] [<c01165e4>] (warn_slowpath_common+0x50/0x68) from [<c00f45dc>] (SYNO_CTRL_INTERNAL_HDD_LED_SET+0x40/0xfc)
[ 50.150000] [<c00f45dc>] (SYNO_CTRL_INTERNAL_HDD_LED_SET+0x40/0xfc) from [<bf23af94>] (synobios_ioctl+0x4ec/0x99c [ds211j_synobios])
[ 50.160000] unwind: Index not found bf23af94
[ 50.160000] ---[ end trace 358c2d4f4263e651 ]---
[ 50.170000] ------------[ cut here ]------------
[ 50.170000] WARNING: at arch/arm/mach-feroceon-kw/./synology-gpio.c:214 SYNO_CTRL_INTERNAL_HDD_LED_SET+0x58/0xfc()
[ 50.180000] Modules linked in: ds211j_synobios(P) sky2 synoacl_ext4(P) synoacl_vfs(P) hfsplus fuse vfat fat cryptosoft ecryptfs sha512_generic sha256_generic sha1_generic ecb cesa_ocf_drv(P) cesa_dev cryptodev(P) ocf(P) chainiv des_generic crc32c eseqiv krng ansi_cprng rng aes_generic md5 cbc cryptomgr pcompress aead crypto_hash crypto_blkcipher crypto_wq crypto_algapi cpufreq cpufreq_stats freq_table dm_snapshot crc_itu_t crc_ccitt quota_v2 quota_tree usbcore sg psnap llc ipv6
[ 50.220000] [<c00efe6c>] (unwind_backtrace+0x0/0xe4) from [<c01165e4>] (warn_slowpath_common+0x50/0x68)
[ 50.230000] [<c01165e4>] (warn_slowpath_common+0x50/0x68) from [<c00f45f4>] (SYNO_CTRL_INTERNAL_HDD_LED_SET+0x58/0xfc)
[ 50.240000] [<c00f45f4>] (SYNO_CTRL_INTERNAL_HDD_LED_SET+0x58/0xfc) from [<bf23af94>] (synobios_ioctl+0x4ec/0x99c [ds211j_synobios])
[ 50.250000] unwind: Index not found bf23af94
[ 50.250000] ---[ end trace 358c2d4f4263e652 ]---
[ 50.250000] Unable to handle kernel NULL pointer dereference at virtual address 0000002c
[ 50.260000] pgd = c6288000
[ 50.270000] [0000002c] *pgd=0627f031, *pte=00000000, *ppte=00000000
[ 50.270000] Internal error: Oops: 17 [#1]
[ 50.270000] last sysfs file: /sys/class/scsi_host/host1/proc_name
[ 50.270000] Modules linked in: ds211j_synobios(P) sky2 synoacl_ext4(P) synoacl_vfs(P) hfsplus fuse vfat fat cryptosoft ecryptfs sha512_generic sha256_generic sha1_generic ecb cesa_ocf_drv(P) cesa_dev cryptodev(P) ocf(P) chainiv des_generic crc32c eseqiv krng ansi_cprng rng aes_generic md5 cbc cryptomgr pcompress aead crypto_hash crypto_blkcipher crypto_wq crypto_algapi cpufreq cpufreq_stats freq_table dm_snapshot crc_itu_t crc_ccitt quota_v2 quota_tree usbcore sg psnap llc ipv6
[ 50.270000] CPU: 0 Tainted: P W (2.6.32.12 #2668)
[ 50.270000] PC is at __gpio_set_value+0x18/0x34
[ 50.270000] LR is at SYNO_CTRL_INTERNAL_HDD_LED_SET+0xc8/0xfc
[ 50.270000] pc : [<c0255c84>] lr : [<c00f4664>] psr: 60000013
[ 50.270000] sp : c62c3e98 ip : c62c3ea8 fp : c62c3ea4
[ 50.270000] r10: 00000000 r9 : c62c2000 r8 : beaeac48
[ 50.270000] r7 : 00000000 r6 : c03e9848 r5 : 00000001 r4 : 00000000
[ 50.270000] r3 : 00000000 r2 : 00000001 r1 : 00000001 r0 : 000000ff
[ 50.270000] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 50.270000] Control: 0005397f Table: 06288000 DAC: 00000015
[ 50.270000] Process scemd (pid: 2513, stack limit = 0xc62c2270)
[ 50.270000] Stack: (0xc62c3e98 to 0xc62c4000)
[ 50.270000] 3e80: c62c3ec4 c62c3ea8
[ 50.270000] 3ea0: c00f4664 c0255c7c beaeac48 beaeac48 00000005 00000000 c62c3ef4 c62c3ec8
[ 50.270000] 3ec0: bf23af94 c00f45ac c62c3f0c c62c3ed8 c01575c8 c0157134 40024000 00000000
[ 50.270000] 3ee0: beaeac48 c0084b0a c62c3f0c c62c3ef8 c01780b4 bf23aab8 c407cd20 beaeac48
[ 50.270000] 3f00: c62c3f7c c62c3f10 c01789f8 c0178090 c5decc80 00000000 c5decc80 c5e99650
[ 50.270000] 3f20: c62c3f44 c62c3f30 c015938c c016461c c5decc80 c4c6bc80 c62c3f84 c62c3f48
[ 50.270000] 3f40: c0159f04 c0159338 40023000 c44af980 00000006 00000000 00000005 beaeac48
[ 50.270000] 3f60: c0084b0a c407cd20 c002c0e8 00000000 c62c3fa4 c62c3f80 c0178a9c c0178400
[ 50.270000] 3f80: c015b180 00000000 00000001 00045f8c beaeacdc 00000036 beaeac5c c62c3fa8
[ 50.270000] 3fa0: c002bf40 c0178a6c 00000001 00045f8c 00000005 c0084b0a beaeac48 00000005
[ 50.270000] 3fc0: 00000001 00045f8c beaeacdc 00000036 00000000 00045df8 beaeae84 beaeac5c
[ 50.270000] 3fe0: 000000cf beaeac48 00020564 406bab3c 20000010 00000005 4098de60 ffffffd0
[ 50.270000] [<c0255c84>] (__gpio_set_value+0x18/0x34) from [<c00f4664>] (SYNO_CTRL_INTERNAL_HDD_LED_SET+0xc8/0xfc)
[ 50.270000] [<c00f4664>] (SYNO_CTRL_INTERNAL_HDD_LED_SET+0xc8/0xfc) from [<bf23af94>] (synobios_ioctl+0x4ec/0x99c [ds211j_synobios])
[ 50.270000] unwind: Index not found bf23af94
[ 50.270000] Code: e59f3020 e1a02001 e7933180 e24cb004 (e593102c)
[ 50.280000] ---[ end trace 358c2d4f4263e653 ]---
Segmentation fault
:: Failed to start scemd. Reboot and get into steel plan or network install mode. ... [ !! ]
[ 52.480000] findhostd uses obsolete (PF_INET,SOCK_PACKET)
[ 53.490000] eth0: no IPv6 routers present
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to[ 59.380000] md: md0 in immediate safe mode
all processes
[ 59.380000] md: md1 in immediate safe mode
Unmounting all file systems.
Unmounting /proc/bus/usb ...
Unmounting /sys ...
Unmounting /dev/pts ...
Unmounting /tmp ...
Unmounting / ...
Unmounting / ...
All file systems unmounted.
Requesting system reboot
[ 65.870000] md: stopping all md devices.
[ 65.870000] md: md1 switched to read-only mode.
[ 65.890000] md: md0 switched to read-only mode.
[ 66.890000] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 67.110000] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 67.130000] Restarting system.
ûþ
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: Synology Disk Station LE

U-Boot 1.1.4 (Jul 14 2010 - 20:36:08) Marvell version: 3.4.4

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B3B4

Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 480Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 6 tRP = 6 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
[4096kB@f8000000] Flash: 4 MB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PEX interface detected Link X1

Synology Model: DS411j
Fan Status: Good

Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
## Booting image at f8080000 ...
Bad Magic Number
Marvell>>

Gruß
Nick

 

[goetz]

Hallo,
Kernel-oops beim Start von scemd, strange. Muß mal ein bisschen nachdenken. Mist, Fluppen neigen sich dem Ende
Flashlayout endlich gefunden, muß noch ein wenig rechnen.

Gruß Götz

 

[Daydreamer]

Wenn wir das wirklich schaffen bekommst Du von mir ne Stange Fluppen!

 

[Daydreamer]

Hi Götz,
lass uns das vertagen. Du hast sicher etwas Schlaf nötig. Dein Elan ist echt bemerkenswert. Ich hab schon ein schlechtes Gewissen.

 

[goetz]

gib mir mal die Ausgabe von
printenv

Gruß Götz

 

[Daydreamer]

Hi Götz,

Marvell>> printenv
bootcmd=bootm F8080000 F8280000
baudrate=115200
loads_echo=0
ipaddr=192.168.101.224
serverip=192.168.101.111
rootpath=/mnt/ARM_FS/
netmask=255.255.0.0
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=cfi_flash:0x380000(root),0x80000(uboot)ro
mainlineLinux=no
CASset=min
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=1
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=::B88FXX81:egiga0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
bootdelay=3
disaMvPnp=no
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS411jv10 ihd_num=4 netif_num=1
ethact=egiga0
ethaddr=00:00:5f:ff:00:00
eth1addr=00:01:5f:ff:00:01

Environment size: 1098/4092 bytes
Marvell>>

Gruß
Nick

 

[Daydreamer]

Sorry die Ip Adressen waren nicht mehr gesetzt. Hier nochmal.

Marvell>> printenv
bootcmd=bootm F8080000 F8280000
baudrate=115200
loads_echo=0
ipaddr=192.168.101.224
serverip=192.168.101.111
rootpath=/mnt/ARM_FS/
netmask=255.255.0.0
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=cfi_flash:0x380000(root),0x80000(uboot)ro
mainlineLinux=no
CASset=min
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=1
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=::B88FXX81:egiga0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
bootdelay=3
disaMvPnp=no
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS411jv10 ihd_num=4 netif_num=1
ethact=egiga0
ethaddr=00:00:5f:ff:00:00
eth1addr=00:01:5f:ff:00:01

Environment size: 1098/4092 bytes
Marvell>> <INTERRUPT>
Marvell>> setenv ipaddr 192.168.123.250
Marvell>> setenv serverip 192.168.123.1
Marvell>> printenv
bootcmd=bootm F8080000 F8280000
baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
netmask=255.255.0.0
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=cfi_flash:0x380000(root),0x80000(uboot)ro
mainlineLinux=no
CASset=min
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=1
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=::B88FXX81:egiga0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
bootdelay=3
disaMvPnp=no
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS411jv10 ihd_num=4 netif_num=1
ethact=egiga0
ethaddr=00:00:5f:ff:00:00
eth1addr=00:01:5f:ff:00:01
ipaddr=192.168.123.250
serverip=192.168.123.1

Environment size: 1096/4092 bytes
Marvell>>

 

[goetz]

Mist, von bootcmd hätte ich ein bisschen was anderes erwartet, seis drum.
Letzter Versuch für heute
tftpboot 0x1000000 zImage
dann
bootm 1000000 F8280000

möglicherweise ist schon die neuere Firmwareversion auf der Platte und der scemd crashed beim älteren Kernel, das aber nach dem Schlaf.
In putty links unter Window bitte mal Lines of scrollback auf 2000 setzen.

Gruß Götz

 

[Daydreamer]

Eventuell wars das schon die DS hat gepiept und taucht im Assistant auf! ;-)
Was soll ich machen?

Gruß
Nick

 

[goetz]

Hallo,
jetzt langsam, Kernel im Flash ist noch korrupt, jetzt mußt Du per ssh als root mit dem Passwort des admin auf die DS.
Per
vi /etc.defaults/VERSION
die buildnumber runtersetzen, Hauptsache kleiner und dann per DSM die aktuelle Firmware einspielen, so DSM per Browser erreichbar.

Gruß Götz

 

[Daydreamer]

Bitte für einfachdenker. Was soll ich machen? "jetzt mußt Du per ssh als root mit dem Passwort des admin auf die DS". Verstehe ich nicht
Gruß
Nick

 

[goetz]

eins ist noch komisch, im Log taucht DS211j auf, die Platten waren da ja mal zur Sicherung drin, hast Du da neu installiert?

Gruß Götz

 

[Daydreamer]

Putty frägt nach einem Passwort.

 

[goetz]

das vom admin

 

[Daydreamer]

Ja das war einer meiner Tests. Ich habe in der alten DS211j zwei Platten mit DSM 4.1 2668 initialisiert in der Hoffnung, dass das was bringt. Der Assistant sagt jetzt auch, dass das System Migriebar wäre. Gruß Nick

 

[Daydreamer]

Es gibt kein admin passwort. Ich hab keines vergeben.

 

[Daydreamer]

Ich hab nix eingeben. Jetzt frägt Putty nach nem "Diskstation Login". Ich kann das von der DS211j versuchen. Oder?
DiskStation login: [ 50.200000] EXT4-fs (md0): barriers disabled
[ 50.210000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 50.270000] synoacl module [synoacl_ext4] is not loaded
[ 50.270000] synoacl module [synoacl_vfs] is not loaded
[ 121.030000] findhostd uses obsolete (PF_INET,SOCK_PACKET)
help
Password:
process '/sbin/getty 115200 con
DiskStation login:

 

[goetz]

welche Firmwareversion hast Du zerlegt und per tftp übertragen? Welche Firmwareversion war auf der DS211j?

 

[Daydreamer]

Die allerletzte 4.1 - 2668 glaube ich ist das.

 

[goetz]

ohne admin Passwort ist ganz Mist, da läßt uns ssh nicht rein. Ganz andere Idee, hast Du noch eine Platte rumliegen die platt gemacht werden kann?