NAS-Daten> dmesg
2303K code, 582K data, 108K init)
Calibrating delay loop... 499.71 BogoMIPS (lpj=2498560)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4096K
NET: Registered protocol family 16
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
DEVICE_CS0 ....base fa000000, size 2MB
DEVICE_CS1 ....base f8000000, size 32MB
DEVICE_CS2 ....base fa800000, size 1MB
DEV_BOOCS ....base ffc00000, size 4MB
Marvell USB EHCI Host controller #0: c0bf3e00
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface 'egiga0' as eth0
o Radom MAC address 00:94:06:d2:72:c7
libata version 1.20 loaded.
sata_sil 0000:01:07.0: version 0.9
drivers/scsi/sata_sil.c (124) Delay 20 seconds to wait for disk ready.
sata_sil 0000:01:07.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xC8800080 ctl 0xC880008A bmdma 0xC8800000 irq 36
ata2: SATA max UDMA/100 cmd 0xC88000C0 ctl 0xC88000CA bmdma 0xC8800008 irq 36
ata1: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4163 85:7469 86:be41 87:4163 88:207f
ata1: dev 0 ATA-8, max UDMA/133, 1953525168 sectors: LBA48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: no device found (phy stat 00000000)
scsi1 : sata_sil
Vendor: ATA Model: WDC WD1000FYPS-0 Rev: 02.0
Type: Direct-Access ANSI SCSI revision: 05
drivers/scsi/sd.c (1711) Internal disk with bus id: 0
SCSI device sda: 1953525168 512-byte hdwr sectors (1000205 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 1953525168 512-byte hdwr sectors (1000205 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
physmap flash device: 400000 at ffc00000
DS406-0: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
DS406-0: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Searching for RedBoot partition table in DS406-0 at offset 0x3b0000
6 RedBoot partitions found on MTD device DS406-0
DS406 flash bank 0: Using RedBoot partition definition
Creating 6 MTD partitions on "DS406-0":
0x003c0000-0x00400000 : "RedBoot"
0x00000000-0x00200000 : "zImage"
0x00200000-0x00380000 : "rd.gz"
0x00380000-0x00390000 : "vendor"
eth0: mac address changed
Mac1: 00:11:32:03:93:06
vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
Vender partition MacNum:1 retlen:64
Serial Number: 83E3N00551
0x00390000-0x003b0000 : "RedBoot Config"
0x003b0000-0x003c0000 : "FIS directory"
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1 29 MB/s
raid6: int32x2 45 MB/s
raid6: int32x4 51 MB/s
raid6: int32x8 48 MB/s
raid6: using algorithm int32x4 (51 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
arm4regs : 429.600 MB/sec
8regs : 369.200 MB/sec
32regs : 513.600 MB/sec
raid5: using function: 32regs (513.600 MB/sec)
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
ds107+_synobios: module license 'Synology Inc.' taints kernel.
synobios: load, major number 201
Brand: Synology
Model: DS-107+
synobios: unload
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 108K
Adding 393584k swap on /dev/hda2. Priority:-1 extents:1 across:393584k
NET: Registered protocol family 5
NTFS driver 2.1.27 [Flags: R/O DEBUG MODULE].
sd 0:0:0:0: Attached scsi generic sg0 type 0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver snd-usb-audio
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
synobios: load, major number 201
Brand: Synology
Model: DS-107+
eth0: link down
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
ehci_platform ehci_platform.4523: (Synology) 88F518x EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.3
usb 1-1: new high speed USB device using ehci_platform and address 2
Got empty serial number. Generate serial number from product.
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver